After making the half scale dress form, I decided I wanted a pants form, too. I thought half scale would be a little big, so I made this one 3/8 scale. I added a torso on top of the pants form to make it a full body form. The form is 21″ tall from top of neck to ankle.
The Amazon product links on this page are affiliate links. If you click on these links and purchase something, I will earn a small commission.
Here are instructions for making the pants form or full body form:
• 1/16″ (2 mm) thick craft foam
• High quality masking tape or clear packaging tape (the thin kind for moving boxes, not the thicker mailing tape). I discovered that thin cheap masking tape will start slipping off after a while.
• Corrugated cardboard
• Manila folder (if you are making a full body form)
• Bamboo or cotton fiber fill
• Scissors that will cut cardboard
• Mechanical pencil or very sharp pencil
• 1″ wide paint brush
• PVA glue (e.g. Elmer’s Glue-All). You’ll need a large bottle – about 7 ounces
• Lightweight spackling compound (optional)
• Fine sandpaper (optional)
• Paint (optional)
• The pants form pattern. If you want to make a full body form, also print pages 2, 3, and 6 of the dress form pattern scaled to 75%. If you want to make a half scale pants form, scale up the pants form pattern 133%.
Print out the pattern(s) (preferably on thick paper). The border around each sheet is 7.5″x10″ when printed with no scaling. Cut out each pattern piece, making sure to cut on the inside edges of the lines.
Determine which side is the right side of each sheet of craft foam, and mark X’s on the wrong side. The foam will bend more easily toward the wrong side.
Trace and cut out each pattern piece from the material indicated on the pattern piece. Again, cut on the inside edges of the lines when you cut out the pieces so they don’t grow larger than the pattern.
• Mark all notch marks on the right side.
• Mark the piece numbers on the foam leg pieces.
• Label foam pieces to indicate if they are for the left or right side of the body.
Some general tips on taping the pieces together:
• Do the taping in a cool room. The tape and foam stretch out of shape if they get too warm.
• Use pieces of tape 1/4″ by 1″ or smaller.
• Butt edges together tightly
• For curved seams, place a small piece of tape on the outside at each end. Tape at any notch marks, then fill in the rest of the seam on the outside.
• Tape the inside of the seam after taping the outside unless directed otherwise.
Tape the darts closed in the WAIST TO HIP FRONT pieces and WAIST TO HIP BACK pieces.
Tape the WAIST TO HIP SIDE BACK pieces to the WAIST TO HIP BACK pieces.
Tape the WAIST TO HIP FRONT pieces to the WAIST TO HIP SIDE BACK pieces.
Tape the cardboard WAIST SUPPORT and HIP SUPPORT pieces to the top and bottom of the assembled WAIST TO HIP foam pieces.
Insert the UPPER CENTER HIP SUPPORT and tape in place.
Tape the dart closed in LEG PIECE #3.
If you want to add an upper torso, assemble the above the waist pieces. See the half-scale dress form tutorial for instructions. Insert the chest support, but don’t use the waist support. Tape the upper torso onto the lower half of the body:
Make a 50/50 mix of Elmer’s glue and water. Pour some of the glue mixture in a small bowl or cup, dip a paintbrush in it, and paint some on a small area of the dress form. Tear off a strip of newspaper, place it on the dress form over the glue, then brush some more glue on top. Keep slightly overlapping pieces of paper until you have a layer done.
In between layers, scribble all over the form with a permanent marker to keep track of your layers, or alternate between text and picture areas on your newspaper. Keep adding layers of paper mache until it seems strong enough. I used five layers of newspaper.